Waste Incinerator Model TS150 PLC, Overview This model is small-scale waste incineration equipment for small waste output. Construction is dual/double combustion chamber with 02 sets oil burner, batch load incineration equipment. Waste feed chamber is 1570Liters (1.57m3, TS150 PLC). Primary & Secondary combustion chambers and smoke filter chamber. Batch load on the bottom of chamber. Read more about 50-100-150-200 Kgs per Hour Solid Waste Incinerator Model TS150 PLC 1570Liters Chamber[…]
Medical waste is posing a growing problem all over the world, jeopardizing the health of staff, patients, disposal workers and anyone else coming into contact with the often hazardous materials discarded by hospitals and other healthcare sites. Hospital waste varies from site to site and the biggest challenge is to dispose of this wide range of waste streams. Incineration is still the preferred way to process medical waste without endangering the heath patients, staff or anyone else coming into contact with them. Clinical waste is costing more and more to dispose of safely. Health Clinics and Health center can now handle their own waste streams using one of our specialist medical incinerators. Destroying hazardous waste at source is by far the most effective and efficient way of handling waste that could potentially spread diseases or viruses. Average 20%-25% of the total waste generated by healthcare establishments is regarded as hazardous and may create a variety of health and environmental risks if not managed and destroyed in an appropriate manner. With years worth of experience in this sector, our medical range of incinerators are designed to cater for the economical needs of small clinics to the more demanding and specialized requirements of large hospitals in their waste management processes. Burring Capacity 100 / 200 KG/ hrNumber of Burner 02 NosIncinerator Type Dual Chamber Primary Chamber Secondy ChamberIncinerator Design Controlled Air Fuel to be used Natural Gas / Deisel Loading System Manual / Batch TypeWarmer Time 20 minutes Type of Paint Heat Resistance enamel paint Chamber Plate Thickness 6mm Chimney Plate Thickness 5mm Thermal Insulation 100 mmRefractory Thickness 100mm Electricity 3 phase 440VComposition of thermal insulator Calcium Silicate slabComposition of refractory High Alumna Cast able 46% AL 2.03 Number of Blowers 02 Nos Temperature controller 02 Nos of digital temperature controllerThermocouple 02 NosWarranty Period 3 Years Chimney Height 40 Ft (first 10 ft SS)(24 inches diameter)Scrubber Wet Scrubber with high pressure water injectionSmokeless Odorless
Air Pollutant Industry Opacity Particulate (Dust) PM10 (mg/Nm3) Sulphur oxide (SOX) (mg/Nm3) Nitrogen oxides (NOX) (mg/Nm3) O2% Carbon monoxide (mg/Nm3) Carbon dioxide (mg/Nm3) Hydrocarbons (mg/Nm3) Hydrogen Sulphide (mg/Nm3) Hydrogen Chloride (mg/Nm3) Hydrogen Fluoride (mg/Nm3) Dioxins/Furans Incinerators * < 10 t: 4g/kg 10 to 30 t: Read more about Incinerator-Air Pollutants[…]
* The second phase of incineration should a post-combustion of the flue gas produced by the combustion chamber at high temperature. * The post-combustion chamber should be situated on the top of the combustion chamber so as to re-burn easily the flue gas. The high content of CO in these gases should permits a re-lighting by simple air injection with the post-combustion burners. This processing is therefore especially well adapted for a treatment on the site. * The post-combustion of gases should takes place at a temperature of 1,100°C during 2 seconds. The cylindrical form of the post-combustion chamber, combined with Vortex effect in the secondary and tertiary air injection, which have must particularly designed and patented , enabling to assure the achievement of very low hydrocarbon refuse. This should contributes also to the limitation of soot (carbon) in the downstream and of the quantity of solid to be treated in the dust remover. * The re-light of the combustion by secondary air with the post-combustion burners and the obtained high temperature of the flame allow to finish the combustion of fine carbonized particles. So, there should be small quantity of unburned flying ashes in the downstream of the furnace. * The design of two post-combustion burners must similar to the combustion burners. * The post-combustion chamber should fitted with inspection doors so that a periodical cleaning of dust can be achieved. * The post-combustion should lined with high thermal insulating materials with a thickness of 150 mm of refractory bricks and 85 mm of insulator.
Application For incineration, general and pathologicalCapacity 50 C 60 kg/h burn rateType Two combustion chambers type; primary and Secondary, controlled/forced combustion air type with a flue gas emission scrubbing unitOperating time Minimum 8 hours dailyOperating temperature From 850 0C to 1200 0C, Automatic controlledResidual Ash 5 to 10%Construction Constructed from heavy duty mild or aluminized steel Orequal and approved equivalentInsulation material Refractory material lining similar or equal to calcium Silicate and hot face combination of heavy duty brickworkInternal Construction Fixed hearth type complete with gratings, concave bottomand charging door, lined with refractory materialCharging Door Suitable for manual loading of wastes and with smooth Dear seal equivalent of Ceramic seals with hinges.Door Lock Automatic, Electric typeAsh removal door Provided, for removing resultant bottom ash leftovers from the Primary chamberGratings ProvidedLoading Manual loading of wastePrimary Burner Fully automatic, with fuel, temperature and speed controls with ignition system, flame detector, Air fan complete with safety features, flame failure, Diesel fired fuel injector type and Flange mounted Blower Provided. For supplying excess combustion air through the distribution system with speed control systemTemperature Minimum exit 850 0CObservation port To be provided with protective glass typeConstruction Constructed from heavy duty mild or aluminized steel or equal and approved equivalentInsulation Refractory material liningCombustion Temperatures Above 850 0C, controlled electronicallyGas residue or retention Time > 2 second at minimum 850 0CSecondary Burner Provided, Diesel fired, fully automatic, with fuel, temperature and speed controls, With ignition system, Flame detector, Air fan, Complete with safety features, flame failure Diesel fired fuel injector type. Flange mountedEjector Provided, Venturi type, for cooling the flue gasesCombustion Air Fan Provided for supplying combustion and creating a negative drift and turbulencesTemperature Maximum 1600 0CConstruction Constructed from heavy duty mild or aluminized steel or equal and approved equivalent Refractory material lining Length 10 m above groundBore about 350mm diameterDischarge temperatures About 850 0CEmissions To comply with standards in section 9 of third schedule of the waste management regulations, 2006.Fully automatic with microprocessor based control unit (PLC) automating all operations of the incinerator. Capable of monitoring all incinerator parameters With large LCD or similar for display of all progressParameters i.e. temperature of primary and secondary chambers, turbulence and timeWith status lampWith user of defined and differed programmed operating cycles for different type of loads/conditionsWith safety interlocks, display of errors and visible and audio alarms.System for continuous emission monitoringSupply and install isolator switch 240V, 100A for the incinerator unit, including all necessary cables 10mSupply and install distribution board. 100 A, complete with MCBs suitable for the rating of the incinerator unit and associated equipment. Wiring to be done according IEE regulations.Make provisions for wiring the isolator switch, Distribution Board control unit to Incinerator and all associated equipment inside to incinerator room. Working length 20m. Wiring to be done using PVC Sheath cable on steel conduits and trucking and in accordance with IEE regulations
Specification for Industrial type Wastage Incinerator Quantity=01 Industrial Type incinerator general specifications-system capacity 100 Kg/h-type of waster: municipal waste (paper, plastic, wood etc)-Waste Feeding: Manual-Fuel: Natural Gas-Incinerator Type Double Chamber-External Cladding: MS sheet of suitable gauge, painted with corrosion resistant paint-Flue Gas Emission Discharged to the atmosphere should meet Pakistan National Environment Quality Standards (NEQS)-User Friendly operation should be ensured by proper automation-Adequate safety features should be incorporated to protect the premises and operators against mishaps and accident Primary ChamberAuto on /off burner-Auto temperature control-excess air blower fanChamber constructed of two layer refractory lining, compressing:Thermal insulator lining & refractory masonry lining sufficient enough to maintain normal temperature at outsideSecondary ChamberPrimary Chamber
7. Type of waste : Bio-medical / Hazardous / Municipal / Trash = ALL and Mixed8. Any other : Rubber, rubber tyres, Batteries, green waste, paper and cardboard9. Quantity of waste generated per day in kg : 3 -5 tonnes per day10. Duration C incinerator will be used per day : 1 C 8 hours / 1 C 16 hours / Continuous 11. Approximate moisture content: Variable12. Local incinerator operating and emission standards : India / EURO / US-EPA Australia13. What is the height of the chimney required? : No chimney is required. Flue length should be approximately 2 to 3 metres to join to a downstream process14. Fuel proposed to be used : LDO / HSD / FO / SKO/ Gas / Other – No fuel required – Intended to free burn waste products15. Availability of power and type : Electricity if required16. Details of space available : Not restricted17. Do you require an automatic loading system? : [X ] Yes [ ] No 18. Do you require a gas scrubbing system? : [ ] Yes [X ] No 19. How soon do you require the system to be delivered? : Sea Freight to Port of Cairns, Queensland, Australia in approximately Two months20. City and country of use : Australia21. Whether the location is a coastal area : [ ]Yes [X ] No 22. Any other specific requirements: Primary combustion chamber only is required. Solid and inflammable waste products need to be capable of being recovered from the incinerator easily using an automated procedure. This is because the incinerator will be required to operate 24/7. Rotary kiln or moving floor may be considered if deemed practical by the supplier. One initial incinerator is required for a proof of concept project and future orders for the successful supplier, following successful implementation of this project, are likely to be significant.23. It would be most useful if the supplier could send a video of the incinerator in operation or diagrams and pictures to show how it works.
Incinerator Burn Rate 65kg/h minimumWeight (kg), please indicate:Secondary ChamberGas Retention Time – 2 SecondsFuel – Diesel/LPG/LNG, please indicatePower Supply for Control Box – 220V-240V 50Hz single phaseMinimum operating temperature 850 °C, please indicateOne year Spare Parts Package for complete maintainability10m Hose Pipe, indicate lengthI000 Litre Fuel Tank + Pipe System, indicate volumeBurn Rate 150kg/h minimumWeight (kg), please indicate:Secondary Chamber Gas Retention Time – 2 SecondsDiesel/LPG/LNG, please indicatePower Supply for Control Box- 220V-240V 50Hz single phaseMinimum operating temperature 920 °C, please indicateOne year Spare Parts Package for complete maintainability10m Hose Pipe, indicate lengthBurn Rate 250kg/h minimumWeight (kg) please indicate:Secondary ChamberGas Retention Time 2 SecondsFuel Diesel/LPG/LNG, please indicatePower Supply for Control Box 220V-240V 50Hz single phaseMinimum operating temperature 920 °C, please indicate One year Spare Parts Package for complete maintainabilityBurn Rate – 150kg/hour minimumWeight (kg), please indicate:Secondary ChamberGas Retention Time 2 SecondsFuel Diesel/LPG/LNG, please indicatePower Supply for Control Box 220V-240V, single phase 50-60HzMinimum operating temperature 1200°C, please indicateOne year Spare Parts Package for complete maintainability
Spare part list – Ignition burner Item description N0 of required Motor 2 Control box 2 Pump couplings 4 Photo cells 2 Sets ht. leads 2 Sets electrodes 4 Oil valve 1 Nozzle 2 Spare part list – After burners Item description N0 of required Motor 2 Control box 2 Pump couplings 4 Photo cells 2 Sets ht. leads 2 Sets electrodes 4 Oil valve 1 Nozzle 2 Spare part list – Ram loader Item description N0 of required Reed switch 4 Seal kit 1 Medical waste incinerator Accessories – Clean out tools – Loading and ash removal methods. – Fuel storage tank with the two pump and all accessories. – Flue gas cleaning system – Stack discharge. – Medical waste incinerator civil work – Construct incinerator foundation – Provide stack support – Provide open steel structure room for the incinerator. Medical waste incinerator submittal shall include:- -Detail installation drawing – Incinerator and auxiliary product data – Test reports – Certificates like CE, ISO, LR, AFNOR, TUV and UL. – Energy analysis report – Project experience – Pollution control equipment emission rate. – Noise level limitation. – Quality assurance – Guarantee
Incinerator Rated Capacity: 100/KG/Hr Type of Design: Double Chambered Mode of Heating: Heating Elements Primary Combustion Chamber Waste Charging Door: Provided with refractory lining with sealing gaskets Ash Removed Door: Provided with refractory lining with sealing gaskets Outer Body MOC: Mild Steel, 5mm Primary Chamber: Stainless Steel Operating Temperature :800. ± 50◦C Insulation: Insulation Brick Heating Elements Type: Kanthal Al Grade Power Consumption: 75 KW ( Initial Load ) Electrical Supply :3 Phase 440 Volt Control Panel MOC: Mild Steel Power Coated No. of Temp: Controllers : 2 Nos Details: The Control Panel will be provided with contract as relays , switches , indicators etc . Operative on 3 phase. I.D.Fan Type: Centrifugal Type MOC: Mild Steel Capacity:2 HP/3Phase Make of Motor: Kirloskar /Havells/Crompton Combustion Air Fan Type: Centrifugal Type Capacity: 1HP/3Phase Make of Motor: Kirloskar /Havells/Crompton Stack: Type: Wire Supported MOC: Mild Steel of ISstd Height :3 Meters or more